Otter Fencing supplies timber bollards for landscaping projects, road and pedestrian management, and fencing applications. We manufacture timber bollards to order, allowing flexibility in size, shape, and design to suit specific project needs. A small selection of timber bollards is also available in stock.
Bollards can be customised with different tops, collars, and chamfer edges to suit various applications. We offer options such as cypress pine, spotted gum, and ironbark, with cypress pine being the most commonly used due to its durability and natural termite resistance.
For additional functionality, bollards can be supplied with drilled chain, pipe, or cable holes, as well as in-ground or collapsible sleeves for secure installation.
Otter Fencing supplies and installs timber bollards across Melbourne and surrounding areas, including Dandenong, Geelong, Keysborough, and Truganina.
Post, Rail and Timber Bollards
Commonly used bollards are, 1.2 to 1.5 meters long and 125, 150 & 200mm square, in both sawn or dressed finishes. When dressed, the sizes are 115mm and 140mm
We can supply bollards up to 300mm square and 6 meters long. The timbers we supply are Cypress Pine, Spotted Gum & Iron Bark. But the most used timber for bollards is Cypress Pine, due too its Class 2 below ground rating, low shrinkage rate of 2.9% and its natural resistance to white ants
Bollard tops can be made in many different shapes and sizes. The size of a chamfered top is most commonly 20mm and a pyramid top is set at 35 degrees (but this is only a guide). We can manufacture your bollard tops to any shape and size, to meet your specifications.
Collar sizes vary from job to job, the same as the bollard tops. We have manufactured them from 4mm to 110mm wide and up to 25mm deep, but the most common size is 18mm wide by 10mm deep and the most common shape is square. Because each job is unique, we have the experience to help you create any shape you require.
We can drill your Chain, pipe or cable holes up to 85mm. Through bollards up to 300mm square or round. We recommend the hole size for pipe, be 5mm bigger than the outside diameter of the pipe required and 3mm bigger for chain and cable.
Impact protection holes are widely used in bollards along road sides parks and reserves to lessen the impact of a vehicle collision. They are usually accompanied by delineators recessed 10mm into the bollards to prevent vandalism. Red delineators on the approach side and white the opposite side. Where scalloped edges are more for decorative purposes. Chamfering the edges of a bollard, also makes a bollard more user friendly by alleviating sharp corners and splinters.
Bollard Sleeves
Bollard sleeves come in below ground and collapsible bollards in above ground only.
In-ground sleeves are concreted 400mm into the ground. The removable sleeve has a concrete strip around the top to allow for a neat and flush finish. Collapsible bolt down sleeves bolt flush to the surface.
Bollards are locked in place by use of the locking tag. The tag is screwed into the bollard once the sleeve has been installed and the correct height has been determined. Once the tag is in place, the lid will close over the tag allowing a padlock to be fitted. Collapsible sleeves have tags already fitted and when upright, the tags will line up and allow you to fit a padlock .
We stock the in-ground bollard sleeves to suit removable bollards in 125mm & 150mm square and the collapsible bollards in 190 x 90 & 140 x 90mm Bolt Down Only.
Otter Fencing provides timber bollards for commercial, industrial, and residential applications across Melbourne and surrounding suburbs. Our service areas include:
- Dandenong
- Dandenong South
- Carrum Downs
- Pakenham
- Altona
- Truganina
- Tullamarine
- Keysborough
- Laverton
- Braeside
- Bayswater
- Campbellfield
- Scoresby
- Epping
- Geelong
We offer expert advice, professional installation, and high-quality materials to meet your specific bollard requirements.